Create your own weaving loom for less than $xx! This budget-friendly project is perfect for the crafty person in your life…fifty-fifty if that person is you lot.

How to Make a DIY Weaving Loom for Less than $20

If you lot've ever wanted to create a weaving from scratch (and not merely one of the many DIY weaving hacks I've put together over the last year), this project is for you.

We made a giant loom (and a small i too), adapted from a project that Jess and her married man whipped upwards a while back, and I'grand sharing the tutorial today.

Surprisingly, making your own loom is really straight frontward and super budget-friendly, if you cull the right materials. And you can hands suit the instructions to the kind of loom you're wanting too – a standing loom (that has legs that boot out for stability) or a lap loom for smaller projects that is more portable, etc.

PLUS, you can customize the size of the loom to whatever dimensions yous want. Click through to brand your own loom from scratch, for under $20!


How to make a giant DIY weaving loom for less than $20

DIY Standing Weaving Loom

The instructions below are for the larger 24×36 inch standing loom. If yous want to make the smaller lap loom, roll down to to the bottom for the materials listing and instructions for the smaller loom.

How to make a giant DIY weaving loom for less than $20

Materials and Tools for DIY Standing Weaving Loom (24×36)

  • one 1×3 select pine board that is 6 ft long (mine toll $5.92)*
  • i 1×3 select pine board that is viii ft long (mine was $8.32)*
  • 1 inch finishing nails or panel board nails (both of these piece of work best because they have a pocket-size head – good for stringing upwardly the loom and removing the finished weaving)
  • eight 1.5 inch screws
  • ruler or tape measure out and pencil
  • hammer and drill
  • 2 inch eye hinges (only demand these if calculation legs to your loom)
  • thin concatenation and 4 centre screws (but need these if calculation legs to your loom)
  • wire cutters (for cutting the chain – again, just need if making legs for loom)

*You can use any type of woods here you'd like, but I used select pine lath to make it expect the all-time it could on a tight budget. If you apply common board, the terminal cost volition exist fifty-fifty cheaper.

And if you employ something like poplar or oak, the last cost volition be a bit more than pine. Each wood blazon will take it's ain pros and cons.

How to make a giant standing loom with $20 and a trip to the hardware store.

Instructions for DIY Standing Loom (24×36)

1. Cut the piece of wood downward to size (the dimensions of each slice of wood are shown in the supplies shot). Then, get-go laying out the pieces to create the loom shape.

I put the ii longer pieces (36 inch pieces) on the bottom and 2 of the shorter pieces (24 inch) on superlative, every bit shown in the photograph.

How to make a giant DIY weaving loom for less than $20

two. Next, brainstorm screwing the pieces together. Yous may want to create a pilot pigsty kickoff to avoid splitting the forest. Just two screws diagonal from each other (as shown in photograph) seemed to work really well for each of the 4 corners.

You can ever do four screws per corner if you lot feel like that's better though. Mine felt actually secure after but 2 screws in each corner though.

Screw all 4 corners the same way, making sure that the corner is squared off before screwing. FYI -Y'all may want to clamp the pieces of woods together offset (if needed) to make sure cipher moves effectually while screwing, etc. Not required though.

How to make a giant DIY weaving loom for less than $20

3. Once the base is complete, you lot tin can either add legs (which I'll testify you how to practise) OR skip this ane and motility onto the side by side step. If you're adding legs, y'all'll employ the remaining two 24 inch pine pieces for the legs.

Flip the loom base over, so that the long vertical pieces are on top (as shown in photograph), then measure 12 inches from the meridian, and attach the hinges to both the loom base and the top of the legs (as shown in photo).

How to make a giant DIY weaving loom for less than $20

From there, you can add screw eyes (one to each of the legs and ane to each of the base pieces across from it) and and so attach the ii together with the sparse chain from the supplies list.

You tin can do this by double or triple knotting one end of the concatenation once it'southward inside the eye of the spiral so bringing information technology across to the other middle spiral (on the leg side for example), and knotting that side around the eye screw also. Making certain the chain is tight when y'all take the leg fully extended to where you want it to be.

And then, repeat this procedure on the other side.

How to make a giant DIY weaving loom for less than $20

4. Next, it'due south time to add together the finishing nails. Make sure the loom is facing right side up (every bit shown in photograph – with shorter horizontal woods base pieces on elevation of the longer ones).

Brand a mark every 1/four inch OR 1/3 inch (this is a preference thing based on how tightly woven you desire your weavings to be), all the fashion across the top horizontal piece of wood and the bottom horizontal piece of wood.

How to make a giant DIY weaving loom for less than $20

Then, hammer a boom in at every mark, in a straight line beyond. Use the photograph for reference.Y'all'll practice that on the height and lesser of the loom and so it's gear up to be strung up for utilise.

How to make a giant DIY weaving loom for less than $20

To create your warp, necktie a knot around the first nail in the upper corner with your yarn / string. Then, keeping tension in the string, bring the string downward to the first smash at the lesser of the loom, wrap around that smash, and proceed dorsum to the meridian of the loom (this time wrapping around the 2d nail).

And then get back downwardly to the bottom second smash, etc. Repeat this process until the unabridged loom is strung and so knot the very last nail on the bottom right to stop it. Cut off excess string from cease of knot and it's ready for weaving.

If y'all're still not sure how to cord your loom, y'all can check out this YouTube video I found for a visual. No need to double up the cord as they did in the video though.

How to make a DIY lap loom for less than $20

DIY Lap Weaving Loom

If y'all're making the smaller lap weaving loom instead of the larger standing weaving loom, the dimensions and materials will exist slightly different. The finished lap loom in the photos is 12×18 inches.

Hither are the materials and instructions for making the DIY lap loom…

Materials and Tools for DIY Lap Loom (12×18)

  • 1 /2 10 ii oak (mine came in a 3 ft pieces and was $6 per slice – I bought 2 pieces to create a loom that was 12×18)
  • ane inch finishing nails or panel lath nails (both of these work best because they accept a small head – skillful for stringing upwards the loom and removing the finished weaving)
  • viii 1 inch screws
  • ruler or tape measure and pencil
  • hammer and drill

The large loom was made with pine and the minor loom was made with oak. Oak is a piffling more than expensive, but looks a trivial nicer, then it'due south kind of a preference thing. You tin can use either one for this projection. Both pine and oak are practiced options.

Instructions for DIY Lap Loom (12×18)

The instructions below are for the smaller 12×18 inch lap loom. If you desire to make the standing loom, scroll upwardly for the materials list and instructions for the bigger loom.

1. Cut the piece of wood down to size – you'll demand two 12 inch long pieces of 1×2 and 2 18 inch long pieces of i×2 for this one.

Then, start laying out the pieces to create the loom shape. I recommend putting the ii longer pieces (18 inch pieces) on the bottom and the ii shorter pieces (12 inch) on top of that. This will give y'all a little more space for hands, etc when weaving afterward.

two. Next, begin screwing the pieces together. You may desire to create a pilot pigsty first to avoid splitting the forest. Just like in the larger loom, 2 screws diagonal from each other seemed to work really well for securing each of the four corners.

You lot can also use finishing nails instead of screws for this if yous prefer, only I would recommend also using some type of wood mucilage in between the 2 pieces of wood if you get that route.

3. At present information technology's fourth dimension to measure for the nails. Make sure the loom is facing right side up (with shorter horizontal forest base pieces on top of the longer ones). Make a mark every i/three inch, all the way across the peak horizontal piece of forest and the bottom horizontal piece of wood.

And so, hammer a nail in at every mark, in a straight line across. You'll do that on the top and bottom of the loom and then information technology'southward ready to exist strung up for employ.

To create your warp, necktie a knot effectually the starting time nail in the upper corner with your yarn / string. Then, keeping tension in the string, bring the string down to the first smash at the bottom of the loom, wrap around that boom, and continue back to the height of the loom (this fourth dimension wrapping effectually the second blast).

Then go back down to the bottom 2nd nail, etc. Repeat this process until the entire loom is strung so knot the very terminal blast on the lesser right to stop it. Cut off excess string from end of knot and it's ready for weaving.

If yous're still not certain how to string your loom, y'all can check out this YouTube video I found for a visual.No need to double up the string equally they did in the video though.

How to make a giant DIY lap loom for less than $20

How to make a giant DIY weaving loom for less than $20

DIY Continuing Weaving Loom (24x36)

Surprisingly, making your ain loom is really straight forwards and super budget-friendly, if you choose the correct materials. And you can easily adapt the instructions to the kind of loom you're wanting also - a standing loom (that has legs that kick out for stability) or a lap loom for smaller projects that is more than portable, etc. PLUS, you can customize the size of the loom to whatever dimensions you want. Click through to brand your own loom from scratch, for under $20!

Keyword: diy loom, weaving loom

Cost: $20

  • one 1x3 select pine board that is six ft long mine cost $5.92*
  • one 1x3 select pine board that is 8 ft long mine was $8.32*
  • 1 inch finishing nails or panel board nails both of these piece of work best because they take a minor head - good for stringing up the loom and removing the finished weaving
  • eight 1.5 inch screws
  • ruler or record measure out and pencil
  • hammer and drill
  • 2 inch center hinges only need these if adding legs to your loom
  • thin chain and four middle screws but need these if adding legs to your loom
  • wire cutters for cut the chain - again, only need if making legs for loom

  • Cut the piece of wood down to size (the dimensions of each piece of wood are shown in the supplies shot). And so, beginning laying out the pieces to create the loom shape.

  • I put the 2 longer pieces (36 inch pieces) on the bottom and 2 of the shorter pieces (24 inch) on top, as shown in the photo.

  • Next, begin screwing the pieces together. You may desire to create a airplane pilot hole kickoff to avert splitting the wood. Just 2 screws diagonal from each other (as shown in photo) seemed to work actually well for each of the 4 corners. You can always exercise 4 screws per corner if y'all feel similar that's meliorate though. Mine felt really secure later on just two screws in each corner though.

  • Screw all 4 corners the aforementioned fashion, making sure that the corner is squared off before screwing. FYI -You may desire to clamp the pieces of forest together first (if needed) to brand certain nothing moves around while screwing, etc. Not required though.

  • In one case the base is complete, you can either add legs (which I'll show you how to do) OR skip this one and move onto the side by side step. If yous're adding legs, you'll apply the remaining two 24 inch pine pieces for the legs.

  • Flip the loom base over, and then that the long vertical pieces are on top (as shown in photo), so measure 12 inches from the meridian, and attach the hinges to both the loom base of operations and the summit of the legs (as shown in photo).

  • From in that location, you can add screw eyes (one to each of the legs and 1 to each of the base pieces across from information technology) and then attach the 2 together with the thin chain from the supplies list.

  • You lot can exercise this past double or triple knotting one end of the concatenation once it's inside the eye of the screw and then bringing it across to the other eye spiral (on the leg side for case), and knotting that side around the center spiral likewise. Making certain the concatenation is tight when you accept the leg fully extended to where you desire it to be.

  • And then, repeat this process on the other side.

  • Side by side, information technology'south time to add the finishing nails. Make sure the loom is facing right side up (every bit shown in photo - with shorter horizontal wood base of operations pieces on top of the longer ones).

  • Make a marker every 1/4 inch OR i/3 inch (this is a preference thing based on how tightly woven you lot want your weavings to be), all the manner across the top horizontal slice of wood and the bottom horizontal piece of wood.

  • And then, hammer a nail in at every mark, in a straight line across. Use the photo for reference. You'll do that on the top and lesser of the loom and and then it's set up to exist strung up for use.

  • To create your warp, tie a knot around the starting time nail in the upper corner with your yarn / cord. Then, keeping tension in the cord, bring the string downwardly to the commencement boom at the lesser of the loom, wrap effectually that blast, and go on dorsum to the top of the loom (this fourth dimension wrapping around the second smash).

  • Then go dorsum down to the bottom 2nd nail, etc. Repeat this process until the entire loom is strung and then knot the very last nail on the lesser right to finish it. Cut off excess string from end of knot and it's ready for weaving.

DIY Lap Weaving Loom

If you lot're making the smaller lap weaving loom instead of the larger standing weaving loom, the dimensions and materials will be slightly different. The finished lap loom in the photos is 12x18 inches.

Keyword: diy loom, weaving loom

Cost: $20

  • one /ii x 2 oak mine came in a 3 ft pieces and was $6 per piece - I bought 2 pieces to create a loom that was 12x18
  • 1 inch finishing nails or console lath nails both of these work best because they have a small head - good for stringing upwardly the loom and removing the finished weaving
  • eight one inch screws
  • ruler or tape measure and pencil
  • hammer and drill

  • Cutting the slice of woods down to size - you'll need two 12 inch long pieces of 1x2 and two xviii inch long pieces of 1x2 for this one.

  • And so, start laying out the pieces to create the loom shape. I recommend putting the ii longer pieces (18 inch pieces) on the bottom and the 2 shorter pieces (12 inch) on elevation of that. This will give you a trivial more infinite for easily, etc when weaving later.

  • Side by side, begin screwing the pieces together. You may want to create a pilot pigsty first to avoid splitting the wood. Just like in the larger loom, two screws diagonal from each other seemed to work really well for securing each of the 4 corners.

  • You can besides use finishing nails instead of screws for this if you prefer, but I would recommend likewise using some type of wood mucilage in between the two pieces of woods if you go that route.

  • At present information technology'south time to measure for the nails. Make certain the loom is facing right side upwards (with shorter horizontal wood base pieces on tiptop of the longer ones). Make a mark every 1/3 inch, all the way beyond the peak horizontal slice of wood and the bottom horizontal piece of forest.

  • And then, hammer a nail in at every mark, in a straight line across. Y'all'll do that on the top and bottom of the loom and so it'southward set to be strung upward for use.

  • To create your warp, tie a knot effectually the first nail in the upper corner with your yarn / string. Then, keeping tension in the string, bring the string downwards to the offset nail at the lesser of the loom, wrap around that nail, and continue dorsum to the acme of the loom (this time wrapping around the second blast).

  • Then go dorsum downward to the bottom second nail, etc. Repeat this process until the entire loom is strung and and then knot the very terminal nail on the bottom right to cease it. Cutting off excess string from end of knot and information technology's ready for weaving.

Photography Brittni Mehlhoff
Crafting assisted by Jess Smith and Cori Maass

And that's how y'all brand your ain weaving loom from scratch on a budget! Information technology'southward difficult to believe that all of the materials toll less than $xx for each loom. Especially since ownership a pre-made version would be at least 5 times that toll! Bully, correct?!

Think you'll make a DIY weaving loom like these guys? If then, which 1 seems more up your alley? The big papa or the baby loom?

Save Save

Relieve Save Save Salve

Relieve Save

Save Save

Save Save

Salve Save

Save Save

Save Salvage

Save Save

Save Save

Salvage Relieve

Save Save

Save Relieve

Save Save

Save Save

Save Save Save Save

Save Salve Save Salvage

Save Save

Save Save

Relieve Salvage

Save Save Salvage Save

Save Save

Relieve Save

Save Save

Save Relieve

Save Salvage

Salve Relieve

Salvage Save Relieve Save

Save Save

Salve Save

Save Salve

Salve Salve